Iai-america RCS-C Bedienungsanleitung Seite 108
- Seite / 119
- Inhaltsverzeichnis
- FEHLERBEHEBUNG
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
98
Code Error Cause/action
0E7 Phase A/B/Z open Encoder signal cannot be detected properly.
Cause: [1] Open encoder extension cable or supplied actuator cable,
or poor connector contact
[2] Faulty encoder
Action: [1] Check the connector for possibility of open circuit, and
examine the connection condition.
(Perform a continuity check by referring to 2-5, “Supplied
Cables.”)
If the cable is normal, the encoder may be faulty. Please
contact IAI.
0F8 Corrupt nonvolatile memory Abnormal data was detected during the nonvolatile memory check at the
startup.
Cause: [1] Faulty nonvolatile memory
[2] The memory was written more than 100,000 times.
(As a rough guide, the nominal life of nonvolatile memory is
around 100,000 rewrites.)
Action: If the alarm occurs again after the power has been
reconnected, please contact IAI.
0F9 Abnormal expansion RAM Abnormal data was detected during the expansion RAM check at the
startup.
Cause: [1] Malfunction due to noise, etc.
[2] Faulty RAM
[3] Faulty circuit component around RAM
Action: Reconnect the power.
If the alarm occurs again, check for effect of noise.
If you have a spare controller, change to the spare controller. If
the alarm still occurs, noise is suspected.
If the cause cannot be specified, please contact IAI.
0FA Abnormal CPU The CPU is not operating properly.
Cause: [1] Malfunction due to noise, etc.
[2] Faulty CPU
[3] Faulty circuit component around CPU
Action: Reconnect the power.
If the alarm occurs again, check for effect of noise.
If you have a spare controller, change to the spare controller. If
the alarm still occurs, noise is suspected.
If the cause cannot be specified, please contact IAI.
0FB Abnormal FPGA The FPGA (gate array) is not operating properly in the absolute
controller.
Cause: [1] Malfunction due to noise, etc.
[2] Faulty FPGA
[3] Faulty circuit component around FPGA
[4] The board in the controller is not installed properly.
Action: Reconnect the power.
If the alarm occurs again, check for effect of noise.
If you have a spare controller, change to the spare controller. If
the alarm still occurs, noise is suspected.
If the cause cannot be specified, please contact IAI.
- RCS Series 1
- ROBO Cylinder Controller 1
- RCS-C Type 1
- CAUTION 2
- Warning 3
- Caution 3
- Before Use 7
- Table of Contents 8
- Absolute Specification 11
- 1. Overview 11
- 1.3 Safety Precautions 13
- 1.5.2 Power Supply 15
- 2.1 Basic Specifications 19
- 2.2.1 Names 21
- 2.2.2 Functions 21
- 2.3.2 Absolute Specification 27
- 2.4 Connection Method 28
- 2.5 Supplied Cable 30
- 2.5.2 Motor Extension Cable 31
- 2.6 Wiring 32
- Home return completion 33
- 2.6.3 PIO Interface 34
- Command position 1 36
- Command position 2 36
- Command position 4 36
- Pin No 36
- Command position 8 36
- Input Part 37
- Output Part 38
- 3.1 Base Specification 39
- 3.2.1 Names 42
- 3.2.2 Functions 42
- 3.3 External Dimensions 48
- 3.3.2 Absolute Specification 49
- 3.4 Connection Method 50
- Battery 51
- 3.5 Supplied Cables 52
- 3.5.2 Motor Extension Cable 53
- 3.6 Wiring 54
- Emergency stop 55
- 3.6.3 PIO Interface 56
- Rectifier 59
- Each output 60
- [A] Push = 0 63
- [B] Push = Other than 0 63
- 4.2 Explanation of Modes 66
- Positioning 68
- 4.2.5 Pause 69
- 4.2.6 Zone Signal Output 69
- 4.3 Timing Chart 70
- 1 msec or less 76
- 5.5 Push & Hold Mode 79
- Moving output ON 83
- 0.1 mm before position 1 83
- 5.8 Pause 85
- 4 msec or less 86
- 4 msec or more 86
- 5.9 Zone Signal Output 87
- 5.10 Returning Home 89
- Position 0 90
- 5.11 Incremental Moves 91
- 6. Parameters 95
- 6.3 Parameter Settings 96
- Movement flag during stop 99
- 6.3.3 Servo Gain Adjustment 100
- 7. Troubleshooting 101
- 7.3 Alarm Output by PIO 102
- (1) Message Alarms 103
- (3) Cold Start Alarms 106
- * Appendix 111
- (Total of both fingers) 112
- Distance from point of action 113
- Point of action 113
- Position Table Record 117
- Parameter Record 118
- IAI (Shanghai) Co., Ltd 119
Verwandte Produkte und Handbücher für Hardware Iai-america RCS-C
Hardware Iai-america E-Con Bedienungsanleitung
(111 Seiten)
(111 Seiten)
Hardware Iai-america PS-24 Bedienungsanleitung
(32 Seiten)
(32 Seiten)
Hardware Iai-america REXT Bedienungsanleitung
(443 Seiten)
(443 Seiten)
© 2020, manymanuals.de. Alle Rechte vorbehalten. | 0.106 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern